PIE Model 532 High Accuracy mA & V Calibrator with Patented Current Leakage Test.
Includes rubber boot, carrying case and FREE NIST Traceable Certificate of Calibration
True ±0.012% of readingaccuracy
4 to 20 mA Loop Functions
Source and Read 0.000-24.000 mA Simulate 2-WireTransmitters
Power 2-Wire Transmitters and Read 0.000-24.000mA
Display current in mA or -25.00-125.00 % of 4-20 mA
Read & Source Voltage Function
Read 0.00 to ± 30.00 VDC with 4X over rangeability Source 0.000 to 24.000 VDC
with up to 20 mA output Direct Calibration1.000V to 5.000V
Full 5 Digit Display
Bar graph for quick reference of input andoutput levels
High contrast graphic display viewable in alllighting conditions and angles
Loop Diagnostic PATENTEDFEATURE
Displays loop current, voltage, resistance, ACvoltage and
mode of operation simultaneously eliminatingmultiple DMM
connections.
Make DYNAMIC loop readings under actualoperating conditions
Included in the loop diagnostic features is itsability to measure ground current leakage from faulty
wiring, flooded conduit,and corrosion bridges. This leakage subtracts from the signal current sensed by
the receiving system (ie: DCS), causing a measurement error.
EZ-DialKnob
Change the speed of dialing your test point byjust pushing down on the knob
Easily adjust output by 0.001 mA (0.01 %) or0.100 mA (1.00 %)
EZ-CheckSwitch with EZ-StepButton
3 position tactile switch with push button fortrue one handed calibrations
Push button for stepping through calibrationpoints
16 different step sizes
Hands-free auto step and auto ramp modes
Selectable soak and step time for working withvalves
The Practical Instrument ElectronicsModel 532 is the best tool for calibration, test, and diagnosing processloops.
The Model 532 brings all the features you would expect from a loopcalibrator and timesaving new ones.
Make adjustments with the EZ-DialKnob or test limits with the dual action EZ-CheckSwitch.
Powerful ramping functions are only abutton away on the Model 532. Save potentially hours of troubleshooting
timeon problem loops with the 532s unique Loop Diagnostic Mode. In LoopDiagnostic Mode, the loop current,
voltage, resistances, AC voltage, and modeof operation are all displayed simultaneously; without the need of
multipleDMM connections. Loop diagnostic is available in every mode of operation andtruly is a diagnostic monitor,
as parameters are continuously updated in realtime. The smart diagnostic tool even indicates the most likely cause of loopfailure!
The Model 532 can detect loop current,voltage, resistance,
AC voltage and HART®
protocol if present in the loop. You are ableto connect the
532 to either side of the loop and in everyoperation mode
diagnose what is happening in the loopwithout the need of a
DMM. Just press the loop diagnostic buttononce
connected and see if there is a problem withthe loop.
General Specifications:
(Unless otherwise indicated allspecifications are rated from a nominal 23 °C, 70 % RH for1 year from calibration)
Operating Temperature Range -20 to60 °C (-5 to 140 °F) Storage Temperature Range -30 to 60 °C (-22 to 140°F)
Relative Humidity Range 10 % ≤RH ≤90 % (0 to 35 °C),Non-condensing
10 % ≤RH≤ 70 % (35 to 60 °C), Non-condensing Size 7.00 X 3.30 X2.21 inches (177.8 x 83.8 x 56.1mm)
Weight 12.0 oz (340 grams)
Battery 9V AlkalineSource/Power and Measure 2-Wire TransmitterSpecifications:
|
≥ 24 Volts |
|
1200 Ω at 20 mA for entire batterylife, 950Ω w/HART® mode enabled |
|
Open loop or out of compliance conditionsare indicated by appropriate error display Battery life in: Source mode ≥ 18 hrs at 12mAtypical (HART® disabled) Power measure ≥ 10 hrs at 12mA typical HART® protocol mode is a selectableoption at turn on. HART® protocol mode places a 250Ω resistor in series with the output Selectable EZ-Step(s) for SourceMode/2-Wire Transmitter Simulation: 2 to 16 selectable step settings
Selectable time settings for stepping andsoak: STEP: 5 to 900 seconds SOAK: 0 to 900 seconds |
